Shopping basket
0 product(s)
progress indicator
Adding product...
The online platform for horticulture Personal advice from our specialists More than 25.000 products More than just a webshop
Specialists: For all your questions about the webshop
+31 174 446 407
Logo image

2C anti Graffity Coat 1 L

Do not delete this link

2C anti Graffity Coat 1 L

Item no. 370012438
box = 12 piece(s)
Price available on request. You can send us your request by clicking on the button below.
Your request will be send to your contact person


2C Anti Graffiti Coat is a transparent, two component, permanent surface protection against graffiti vandalism based on nanotechnology. Surfaces treated with the 2C Anti Graffiti Coat are easy to clean and maintain their shine. Furthermore the surfaces are long-term protected against weather influences by a UV filter.

2C Anti Graffiti Coat is used as a wear-resistant, chemical resistant and non-yellowing transparent permanent anti-graffiti coating on painted surfaces, metal and all other kinds of mineral surfaces.

- Prolonged protected from weather influences (10 years)
- Dirt no longer adheres to the surface and is easy to remove
- Less maintenance and cleaning
- Long-time shine
- Easy application

- Aluminium siding
- Powder coated surfaces
- Steel surfaces
- Trespa cladding
- Mineral substrates

Main features
- Treated parts are well protected against the adhesion of dirt
- UV Filter prevents discolouration
- Get discoloured parts in most cases their original colour
- Product is silicone free
- The nano-coated layer provides a very long lasting protection against pollution

Processing Advice
The surface must be dry and free of grease, oil and dust.

- Shake NC Cleaner before use
- Apply by spraying
- Clean with a soft cloth, sponge or brush. If necessary, rinse with water and dry by pulling large
areas with wiper

After drying, apply 2C Anti Graffiti Coat preferably sprayed with XVLP syringe in a wet film thickness of
about 20 to 25 uM / 5-15 uM dft.


Mixing ratio
Base: hardener = 3:1 (e.g. 30 parts by volume base + 10 parts hardener)
Basic ingredient + hardener merge mix well and let stand for approximately 20 minutes
- Apply with brush, roller and spray . Up to 5% with butanol.
- The temperature of the mixture of base component and curing agent should be preferably above 15 ° C,
dilution should be added in order to obtain the proper application viscosity at lower temperatures.
- Too much dilution results in a reduced sag resistance and slows the curing.
- Add Dilution after mixing of the components.

Processing times
Induction time : 20 minutes C. A.
Processing time : 5 hours at 23°C / 55% relative humidity
To touch : 90 minutes at 23°C / 55% relative humidity
By Dried : 6 hours
Full cure : 48 hours
Brush/ Roller
Recommended paint roller: roller of polyester foam
XVLP sray equipment
Dilution : 0-5 vol% butanol Nozzle : position 5 Air volume : 50 to 70% Cleaning tools : butanol Colour and Shine
- Transparent
- Dries colourless
- Visible, silk gloss

- Bottle of 1 litre
- Jerry cans of 5 litres and 10 litres

Theoretical yield: 40-60 m2
*This indicated consumption is a reference value. Depending on the nature of the surface and the processing it may vary. Exact values can only by determined per project through plots.

Processing conditions
During the installation of the 2C Anti Graffiti Coat, the humidity should not exceed 85% and should be minimum of 3ºC above the dew point temperature of the surface to be treated.
Before 2C Anti Graffiti is applied to a concrete surface, it is important that the moisture content does not exceed 4%

Cleaning coated surfaces
Treated surfaces can be cleaned with a biodegradable solvent and about 80-120 bar water pressure. Local laws and regulations regarding disposal must be observed. At least depending on the degree of pollution it is possible that the cleaning should be performed multiple times.