Home ​​​​>​​​​ Knowledge Center​​​​

How do you install new substrates in a greenhouse?

In many cases, a new crop cycle starts with a new substrate, as this is more hygienic than reusing existing substrate mats. After you have chosen the right substrate mat, your order is delivered and you can start working with the new substrate after having removed the previous crop. It is important that you handle the substrate mats correctly. That is why we list a number of points of attention for you and offer advice for installing new substrate mats.
Substrate Mats in a Greenhouse
Roel Bijl
Product Specialist Plant Resilience and Substrates | March 18, 2020 | 4 min. reading time

Taking delivery

  • If you will not be using the new substrate mats immediately after receipt, store them in a clean and dry place. We strongly advise against storage outside.
  • Place the pallets at a location outside the production area, where the substrates cannot be damaged by employees or transport equipment. This is because damage can cause inequality in initial saturation, poor crop rooting and inequality in plant structure.
  • Keep the delivery data to ensure the traceability of the substrate mats (e.g. the retrieval codes).

Installing the substrate mats

  • Place the mats with the right side up (check the arrow and read the text on the film).
  • If you ordered substrate mats without pre-perforated plant holes, determine what interspacing you want to apply between the plant holes.
  • Insert the irrigation pins. Make sure that the pins do not pierce through the mat.
  • Crops should not be planted on dry mats. Therefore, the substrate should be filled with the nutrient solution suitable for your crop at least 48 hours before planting. Make sure that the solution is warm (> 18°C), so that the young plants do not suffer from cold shock.
  • Check to ensure all mats are properly filled. If the substrate mat is fully filled, the packaging film becomes lumpy, while the nutrient solution can be seen on the surface of the mat. If the mat is not full, fill it up manually using a watering can.
  • In order to ensure maximum capillary action of the substrate mat, the mat must remain fully saturated for at least 24 hours. An exception applies in the event of extremely high temperatures: in that case, fill the mats at night so that the solution does not become too hot. This is because an excessively hot solution (> 26°C) increases the risk of Pythium.
  • Create drainage holes in the substrate mats at least 24 hours before planting. Do this correctly, to ensure you obtain the best crop results.
In this video, we show you how to make drain holes in a rock wool mat. 

Plants

  • Discuss with your supplier the conditions under which the plants are transported so you can be sure that the plants are delivered in a good condition.
  • A temperature between 18°C and 28°C offers the best conditions for the plants to root. Therefore, make sure that the greenhouse and the substrate are at the right temperature.
  • Prevent cold shock by moving the plants directly to the greenhouse and planting them as quickly as possible.
Related products
Contact form
Can't find your answer? Fill out the contact form and our specialist Roel Bijl will get back to you. On weekdays, even within 24 hours.

How do you install new substrates in a greenhouse?

In many cases, a new crop cycle starts with a new substrate, as this is more hygienic than reusing existing substrate mats. After you have chosen the right substrate mat, your order is delivered and you can start working with the new substrate after having removed the previous crop. It is important that you handle the substrate mats correctly. That is why we list a number of points of attention for you and offer advice for installing new substrate mats.
Search in the Knowledge Center
​​​​​​​​Find answers to your question in our Knowledge Center. 600+ articles, written by our specialists.​​​​
Categories:
Roel Bijl Product Specialist Plant Resilience and Substrates
Roel Bijl
Product Specialist Plant Resilience and Substrates | March 18, 2020 | 4 min. reading time
Share this article
Substrate Mats in a Greenhouse

Taking delivery

  • If you will not be using the new substrate mats immediately after receipt, store them in a clean and dry place. We strongly advise against storage outside.
  • Place the pallets at a location outside the production area, where the substrates cannot be damaged by employees or transport equipment. This is because damage can cause inequality in initial saturation, poor crop rooting and inequality in plant structure.
  • Keep the delivery data to ensure the traceability of the substrate mats (e.g. the retrieval codes).

Installing the substrate mats

  • Place the mats with the right side up (check the arrow and read the text on the film).
  • If you ordered substrate mats without pre-perforated plant holes, determine what interspacing you want to apply between the plant holes.
  • Insert the irrigation pins. Make sure that the pins do not pierce through the mat.
  • Crops should not be planted on dry mats. Therefore, the substrate should be filled with the nutrient solution suitable for your crop at least 48 hours before planting. Make sure that the solution is warm (> 18°C), so that the young plants do not suffer from cold shock.
  • Check to ensure all mats are properly filled. If the substrate mat is fully filled, the packaging film becomes lumpy, while the nutrient solution can be seen on the surface of the mat. If the mat is not full, fill it up manually using a watering can.
  • In order to ensure maximum capillary action of the substrate mat, the mat must remain fully saturated for at least 24 hours. An exception applies in the event of extremely high temperatures: in that case, fill the mats at night so that the solution does not become too hot. This is because an excessively hot solution (> 26°C) increases the risk of Pythium.
  • Create drainage holes in the substrate mats at least 24 hours before planting. Do this correctly, to ensure you obtain the best crop results.
In this video, we show you how to make drain holes in a rock wool mat. 

Plants

  • Discuss with your supplier the conditions under which the plants are transported so you can be sure that the plants are delivered in a good condition.
  • A temperature between 18°C and 28°C offers the best conditions for the plants to root. Therefore, make sure that the greenhouse and the substrate are at the right temperature.
  • Prevent cold shock by moving the plants directly to the greenhouse and planting them as quickly as possible.
Related products
Contact form
Can't find your answer? Fill out the contact form and our specialist Roel Bijl will get back to you. On weekdays, even within 24 hours.
Roel Bijl Product Specialist Plant Resilience and Substrates
Also interesting for you
What are the risks of reusing substrate mats?
For economic reasons some growers opt to reuse the substrate mats. Note that this does involve various risks, such as the risk of infection by pathogens, reduced water capaity and slower rooting.

How to create drainage holes in the substrate mats?
The number of drainage holes and the position of these holes have a major impact on the crop. This is because these are in part decisive for the water flow in the substrate, the re-saturation capacity and the displacement of old nutrient solutions.
What is the difference between cultivation on Rockwool substrate and cultivation on cocopeat?
Cocopeat has been used as a substrate for many years. In this article, our specialist further explains the differences between cultivation on Rockwool substrate and cultivation on cocopeat.