Home ​​​​>​​​​ Knowledge Center​​​​

How to calibrate an EC meter?

With the EC meter you are able to measure the concentration of the total amount of dis-solvable salt in a liquid. Therefore the EC meter is an important tool to control and adjust the fertilizer strategy and the feeding schedule. After using the EC meter for a longer period it is possible that because of filth and wearing of the electrodes a wrong measuring will occur. That’s why it’s important to regularly calibrate your EC meter. When you do this you compare your measurement with the international standard values. But how does this work?
Frank Schoenmakers
Specialist Mechanical Equipment | April 16, 2020 | 4 min. reading time
EC meter

How often do you calibrate

The frequency of calibrating is different for every company. Because it depends on how many times the EC meter is used and the amount of filth in the EC meter. The higher these numbers are, the more you need to calibrate. We advise that you calibrate your EC meter a minimum of 2 times per month. It’s also wise to calibrate in the following situations:
  • When u use a new electrode
  • When the electrode hasn’t been used for a long time
  • After the electrode has been cleaned
  • When u used the meter in a powerful solution
  • When it’s important to get a very exact measurement

Preparation

A new electrode or one that hasn’t been used for a long time have to be cleaned first to get a good measurement.

Calibrating the EC meter

  • For calibrating you choose the calibration with the value that comes closest to the measurements that you see most often. In horticulture in most cases this is 12,84mS (an EC of 12,84). Use calibration liquid with every calibration.
  • Put the electrode in the calibration liquid. After about one minute the measuring is stable. The EC meter is supposed to measure 12.840µS when you use 12,84mS of calibration liquid. If this is not the case then u set the EC meter on this value (the further the measured value is away from the real value, the bigger the deviation of the device).
  • After calibrating you have to clean the electrode with deminalized water and place it in the calibration liquid again. Repeat these steps until you get a reliable measurement.

Inspecting the Elmeco EC meter

Not every EC meter can be calibrated by you. This is also the case with the Elmeco EC-meter: you can only check it and not calibrate it yourself. Checking is done as follows:
  • Turn on the EC meter
  • Fill the cup with the calibration fluid until it is completely full.
  • Wait a few minutes until the measurement is stable.
  • If the indicated EC-value differs a lot from the value of the calibrating fluid, have the EC-meter repaired.
The video above shows how to check an Elmeco EC-meter.  

Difference between calibrating and fine tuning

In most cases calibrating and fine tuning are being defined as the same. However these are two different things. With ec meter calibration you define how far the EC meter deflects from the standard. This is something you can do yourself without consequences: u only set the accuracy of the instrument. Fine tuning is an official examination by a specialist who determines in what way the EC meter satisfies to the legal prescriptions. When the EC meter does not meet the legal prescriptions it will be disapproved and may not be used any longer.
Contact form
Can't find your answer? Fill out the contact form and our specialist Frank Schoenmakers will get back to you. On weekdays, even within 24 hours.

How to calibrate an EC meter?

With the EC meter you are able to measure the concentration of the total amount of dis-solvable salt in a liquid. Therefore the EC meter is an important tool to control and adjust the fertilizer strategy and the feeding schedule. After using the EC meter for a longer period it is possible that because of filth and wearing of the electrodes a wrong measuring will occur. That’s why it’s important to regularly calibrate your EC meter. When you do this you compare your measurement with the international standard values. But how does this work?
Search in the Knowledge Center
​​​​​​​​Find answers to your question in our Knowledge Center. 600+ articles, written by our specialists.​​​​
Frank Schoenmakers
Frank Schoenmakers
Specialist Mechanical Equipment | April 16, 2020 | 4 min. reading time
Share this article
EC meter

How often do you calibrate

The frequency of calibrating is different for every company. Because it depends on how many times the EC meter is used and the amount of filth in the EC meter. The higher these numbers are, the more you need to calibrate. We advise that you calibrate your EC meter a minimum of 2 times per month. It’s also wise to calibrate in the following situations:
  • When u use a new electrode
  • When the electrode hasn’t been used for a long time
  • After the electrode has been cleaned
  • When u used the meter in a powerful solution
  • When it’s important to get a very exact measurement

Preparation

A new electrode or one that hasn’t been used for a long time have to be cleaned first to get a good measurement.

Calibrating the EC meter

  • For calibrating you choose the calibration with the value that comes closest to the measurements that you see most often. In horticulture in most cases this is 12,84mS (an EC of 12,84). Use calibration liquid with every calibration.
  • Put the electrode in the calibration liquid. After about one minute the measuring is stable. The EC meter is supposed to measure 12.840µS when you use 12,84mS of calibration liquid. If this is not the case then u set the EC meter on this value (the further the measured value is away from the real value, the bigger the deviation of the device).
  • After calibrating you have to clean the electrode with deminalized water and place it in the calibration liquid again. Repeat these steps until you get a reliable measurement.

Inspecting the Elmeco EC meter

Not every EC meter can be calibrated by you. This is also the case with the Elmeco EC-meter: you can only check it and not calibrate it yourself. Checking is done as follows:
  • Turn on the EC meter
  • Fill the cup with the calibration fluid until it is completely full.
  • Wait a few minutes until the measurement is stable.
  • If the indicated EC-value differs a lot from the value of the calibrating fluid, have the EC-meter repaired.
The video above shows how to check an Elmeco EC-meter.  

Difference between calibrating and fine tuning

In most cases calibrating and fine tuning are being defined as the same. However these are two different things. With ec meter calibration you define how far the EC meter deflects from the standard. This is something you can do yourself without consequences: u only set the accuracy of the instrument. Fine tuning is an official examination by a specialist who determines in what way the EC meter satisfies to the legal prescriptions. When the EC meter does not meet the legal prescriptions it will be disapproved and may not be used any longer.
Contact form
Can't find your answer? Fill out the contact form and our specialist Frank Schoenmakers will get back to you. On weekdays, even within 24 hours.
Frank Schoenmakers
Also interesting for you
How to calibrate a pH meter
The fluids in the electrode of a pH meter age the longer the meter is being used. This causes measuring error in the instrument. You can determine this measuring error by calibrating your pH meter. Our specialists provide you tips how to calibrate your pH meter.
How do you calibrate a CO2 meter?
If you use a CO2 meter for a longer period, a measurement error can occur in the meter. You can determine this by calibrating the CO2 meter.


How does a manometer work?
A manometer is a measuring instrument that measures the pressure of a liquid or gas in an enclosed space, for example in a boiler.